|
|
|
|
| |
|
| Product |
Description |
|
| |
Model FW-5A
SKU : Model FW-5A
Price : $1,026.00
|
Sale price: $1026.00
List price: $1080.00
The Model FW-5A is equipped with a precision air regulator which enables the process controller output to the heatgun heater element control circuit only if an adequate air source is connected. The process controller is equipped with a digital display which shows the real time temperature of the heated air flowing out from the heatgun element.
The desired air temperature can be programmed into the controller and can be changed as welding conditions vary. The control box is equipped with two separate switches, where the HEAT switch will not work unless the MAIN POWER switch is enabled. Note that the MAIN POWER switch is also an overcurrent protection device. |
|
| |
Model FW-5B
SKU : Model FW-5B
Price : $846.00
|
Sale price: $846.00
List price: $890.00
The Model FW-5B is equipped with a precision air regulator which enables the process controller output to the heatgun heater element control circuit only if an adequate air source is connected. The process controller is potentiometer controlled, from several LOW thru HIGH settings. Heatgun air temperature is controlled by turning the knob clockwise for higher air temperatures.
The control box is equipped with two separate switches, where the HEAT switch will not work unless the MAIN POWER switch is enabled. Note that the MAIN POWER switch is also an overcurrent protection device |
|
| |
Model FW-5C
SKU : Model FW-5C
Price : $1,121.00
|
Sale price: $1121.00
List price: $1180.00
The Model FW-5C includes an internal air compressor that is incorporated into the control box. The AIR SUPPLY INLET is equipped with an air filter. The process controller is equipped with a digital display which shows the real time temperature of the heated air flowing out from the heatgun element.
The desired air temperature can be programmed into the controller and can be changed as welding conditions vary. The control box is equipped with two separate switches, where the HEAT switch will not work unless the MAIN POWER switch is enabled. Note that the MAIN POWER switch is also an overcurrent protection device. |
|
| |
Model FW-5D
SKU : Model FW-5D
Price : $912.00
|
Sale price: $912.00
List price: $960.00
The Model FW-5D includes an internal air compressor that is incorporated into the control box. The AIR SUPPLY INLET is equipped with an air filter. The process controller is potentiometer controlled, from several LOW thru HIGH settings. Heatgun air temperature is controlled by turning the knob clockwise for higher air temperatures.
The control box is equipped with two separate switches, where the HEAT switch will not work unless the MAIN POWER switch is enabled. Note that the MAIN POWER switch is also an overcurrent protection device. |
|
| |
Model 41-HT-350
SKU : Model 41-HT-350
Price : $405.00
|
The Model 41-HT used for tack welding or hand welding with round tips at speeds of approximately 12 inches (300 mm) per minute. It is ideally suited for back welding of pipe , short radii, or hard-to-reach areas. It operates on shop air or inert gas. The standard stainless-steel heating element for this welder is rated at 350 watts. An air regulator, pressure gauge and complete operating and maintenance instructions are furnished. Tips and accessories must be ordered separately. |
|
| |
Model 41-HT-450
SKU : Model 41-HT-450
Price : $415.00
|
The Model 41-HT is used for occassional high-speed welding using 1/8" or 5/32" rod. It operates on shop air or inert gas. The standard stainless-steel heating element for this welder is rated at 450 watts. An air regulator, pressure gauge and complete operating and maintenance instructions are furnished. Tips and accessories must be ordered separately. |
|
| |
Model 42-TM-350
SKU : Model 42-TM-350
Price : $561.00
|
Trainer and maintenance kit which includes Model 41-HT along with a 350 watt stainless steel element, air regulator and pressure gauge, KR round tip, KT tacker tip, aluminum welder stand, and a steel carrying case. This model contains everything needed for training as well as for fabricating and maintenance. Operates on shop air or inert gas. |
|
| |
Model 42-TM-450
SKU : Model 42-TM-450
Price : $580.00
|
Trainer and maintenance kit which includes Model 41-HT along with a 450 watt stainless steel element, air regulator and pressure gauge, KR round tip, KT tacker tip, aluminum welder stand, and a steel carrying case. This model contains everything needed for training as well as for fabricating and maintenance. Operates on shop air or inert gas. |
|
| |
Model 43-HS-600
SKU : Model 43-HS-600
Price : $570.00
|
A heavy-duty welder for medium and high speed welding of thermoplastics with welding speeds up to 60" (1520 mm) per minute. The standard electric stainless steel heating element is rated at 600 watts. This lightweight hot gas welder can be used with all types of weldable thermoplastics having a minimum thickness of 1/16". An air regulator, pressure gauge and complete operating and maintenance instructions are furnished. Tips and accessories must be ordered separately. Additional elements available in 750 or 900 watt ratings. Operates on shop air or inert gas. |
|
| |
Model 43-HS-900
SKU : Model 43-HS-900
Price : $591.00
|
A heavy-duty welder for medium and high speed welding of thermoplastics with welding speeds up to 60" (1520 mm) per minute. The standard electric stainless steel heating element is rated at 900 watts. This lightweight hot gas welder can be used with all types of weldable thermoplastics having a minimum thickness of 1/16". An air regulator, pressure gauge and complete operating and maintenance instructions are furnished. Tips and accessories must be ordered separately. Additional elements available in 600 or 750 watt ratings. Operates on shop air or inert gas. |
|
| |
|
Page 1 of 35 Next
|
